|
Power amplifier (CE) |
|
|
Power
|
12Watt(12V@1A)
|
|
Compliance voltage
|
±12V |
|
Max. current |
±1A |
|
Control speed selection |
4 ea |
|
Bandwidth |
2MHz |
|
Slew rate |
10V/usec |
|
Potentiostat mode(voltage control) |
|
|
Voltage control |
|
|
- Control voltage range |
±10, ±1V, ±100mV |
|
- Voltage resolution |
16 bit per each range |
|
- Voltage accuracy |
±0.02% fs(gain x1)
|
|
- Max. scan range |
±10V vs. ref. E |
|
Current measurements |
|
|
- Current range |
9 ranges (auto/manual setting)
100nA ~ 1A (10nA with gain) |
|
- Current resolution |
16 bit;
30uA, 3uA, 300nA, 30nA, 3nA, 300pA
30pA, 3pA (300fA with gain) |
|
- Current accuracy |
±0.05% f.s.(gain x1) >100nA
|
| Galvanostat mode(current control) |
|
| Current control |
|
|
- Control current range
|
max. ±1A
± full sacle depending on selected range
|
|
- Current resolution
|
16 bit;
30uA, 3uA, 300nA, 30nA, 3nA, 300pA
30pA, 3pA (300fA with gain)
|
|
- Current accuracy
|
±0.05% f.s.(gain x1) >100nA f.s.
|
| Voltage measurements |
|
|
- Voltage range
|
10V, 1V, 100mV |
|
- Voltage resolution
|
16 bit; 0.3mV, 30uV, 3uV
|
|
- Voltage accuracy
|
±0.02% fs(gain x1)
|
| Electrometer |
|
|
Max. input voltage
|
±10V |
|
Input impedance
|
2x1013Ω||4.5pF
|
|
Bandwidth
|
>22MHz
|
|
CMRR
|
>114dB
|
| EIS(Internal FRA) for system |
|
|
Frequency range
|
10uHz ~ 1MHz
|
|
Frequency accuracy
|
<0.01%>
|
|
Frequency resolution
|
5000/decade
|
|
Amplitude
|
0.1mV ~ 5V rms (potentiostatic)
0.1 ~ 70% f.s. (galvanostatic)
|
|
Mode
|
Static EIS:
potentiostatic, galvanostatic,
pseudo-galvanostatic, OCP
Dynamic EIS:
potentiodynamic, galvanodynamic
Fixed frequency impedance:
potentiostatic, galvanostatic,
potentiodynamic, galvanodynamic
Multisine EIS:
potentiostatic, galvanostatic
|
| Main system |
|
|
PCcommunication
|
USB2.0 high speed
|
|
Line voltage
|
100~240VAC, 50/60Hz, 1Amp
|
|
Max. channel number per unit
|
8 independent channel per unit
|
|
Max. channel
|
16 channels expandable per PC
|
|
Size
|
448x426x208mm(WxHxD)/8ch housing system
|
| Software |
|
|
Max. steps per experiments
|
1000
|
|
Shutdown safety limits |
voltage, current, power, auxV, etc. |
|
Max. sampling rate |
2usec or 3usec depending on data point numbers |
|
Min. sampling time |
unlimited |
|
Sampling condition |
time, dv/dt, dI/dt, etc.
|
|
Interface for system |
|
|
Auxiliary port |
|
|
- Auxiliary voltage input
|
1 analog input: ±10V
|
|
- Zero resistance ammeter
|
100nA~1A ranges
|
|
- External booster interface
|
via booster I/F cable
|
|
Channel System
|
|
|
Cell cable
|
1 meter shielded type (standard)
working, reference, counter, working sense,
auxiliary V+, AuxV-
|
|
Control
DAC
|
DSP with FPGA
2x16bit DAC(50MHz) for bias & scan
|
|
Dataacquisition
ADC
|
2x16bit ADCs(500kHz) for voltage & current
1x16bit ADCs(250kHz) for auxiliary reading
|
|
Calibration
|
automatic
|
|
Filter
|
4ea (5Hz, 1kHz, 500kHz, 5MHz)
|
|
Scan rate
|
0 ~ 200V/sec in common mode
0 ~ 5000V/sec in fast mode
|
|
Front panel LED
|
busy, run
|
|
Internal data memory
|
542,000 points
|
|
Max. output power
|
12Watt per channel
|
|
PC requirement
|
|
|
Operating system
|
WindowsXP SP3/7/8/10(32bit/64bit)
|
|
PC specification(minimum)
|
Pentium4, RAM 1GB or higher
|
|
Display
|
1600x900 high color or higher
|
|
USB
|
high speed 2.0
|
|
General
|
|
|
Dummy cell
|
one external dummy cell included
|
|
Impedance analysis software
|
ZmanTM
|
|
DC data analysis software
|
IVMANTM
|
